Shimano Spinners modification (bearings mod & Servicing)

2»
  • fishyton
    Slide the rear protector over and the rear seal to the back of the reel body and it is time to secure the rear plate by tightening the screw inside that rear protector collar.

  • fishyton


    The above picture shows the pinion gear bearing retainer is held by 3 screws.
    Forgotten to take a pic to show that pinion gear bearing before i secure its retainer.




    Picture of the reverse side of the Roller clutch assembly with the bean shaped clutch insole.

  • fishyton

    Clutch assembly housing in positioned. Noted that the u-groove of the clutch insole must sit onto the anti-reverse cam. Sorry i forgotten to take a pic again.


    6 pieces of Clutch rollers in placed.



    Followed by putting in the clutch springs.
    I use a pair of tweezer to pick up the spring, place it into the slot carefully while your finger is covering half of the slot.
    Use the pointed edge of the tweezer to push tbe spring into the slot carefully.
    Be really patient here as you wanna avoid sending the springs into the air.
  • fishyton
    After you are done with the rollers and springs, placed the Clutch outer spacer (a white plastic ring spacer) and the clutch cover and secure it with the octagon shaped retainer.
    Lastly slot the rotor ring tru the mainshaft.



    Finally check if the anti reverse clutch is functioning properly.
  • The_Clairvoyant
    Hi, may I know where can I find such a small allen key?
    I use a pair of needle nosed tweezers for the small screw on the stella spool shaft but its really difficult to remove and replace
  • fishyton
    Hi Sorry for overlooking your question on the Allen Key.
    Have not been doing modds and servicing for quite some time due to other commitments.
    I got the Allen key from Daiso
  • sgbdk
    edited March 2014
    Hi bro.. pmed you on charges for reel servicing
  • Lester89
    Bro are u still doing reel servicing?
  • fishyton
    Hi bro, im not doing reel servicing anymore due to commitments.
    A proper n thorough service really sucks up too much time especially so when u are given a reel which is really in a bad shape.
  • fishyton
    edited July 2014
    I have received many pm from kakis who have expressed interest in reel modification.
    My opinion is the best platform for modification is the 2011 shimano Twinpower Xship 1000-4000 size because the Twinpower platform share many similarities with the 12' Vanquish and 10' Stella body.
    With a little tweak, you can enjoy the price of a TP with the performance and smoothness close to that of a Vanquish or even a Stella.

    Stock 2011 Twinpower comes with 9 bearings.
    Possible enhancement is to add 3 more bearings to the drivetrain.

    Improvements:
    1) More torque translate to improved cranking power
    2) Less friction to oscillation shaft
    3) Smoother overall operation

    A) To replace the Oscillation worm Shaft front and rear plastic bushings:
    > you will need x2 (3x6x2.5mm) bearings



    Oscillation Worm Shaft mod: 3x6x2.5mm bearing x2
  • physlo2
    Thanks for sharing. I assume it is the same as the Twinpower 08 models as well right?
  • Wei_Lian
    Bro, twinpower c3000hg can?
  • bryanpoh66
    Hi I'm Bryan want to service my Stella 6000 contact me @85115577
  • fishyton
    physlo2" said:
    Thanks for sharing. I assume it is the same as the Twinpower 08 models as well right?
    Bro, Looking at the 08' TP schematics, it should be the same. :)
    The main difference is that 08 model does not have xship technology, the pinion gear is supported by Only ONE ball bearing with the other end on a plastic bushing.
  • fishyton
    Wei_Lian" said:
    Bro, twinpower c3000hg can?

    Hi 'mate,

    The modd is applicable for:

    Twinpower 1000, 2500/S, C3000, C3000HG, 4000 and 4000XG.
  • fishyton
    bryanpoh66" said:
    Hi I'm Bryan want to service my Stella 6000 contact me @85115577
    Hi Bryan, i no longer do servicing anymore due to time and work commitments.
    I guess there are other kakis here which do offer such services as well.
    My sincere apologies.
  • Lester89
    Bro u have the oscillating paw bearing for shimano stradic?
  • shukran1209
    Hi Fishyton,

    Good day to you,

    Saw this tread and would like to get in touch with u to service my spinning reels.

    Shimano Stella 2013 C3000 & SW8000PG   Twinpower 2015 SW4000XG & SW5000PG
    Stradic New Model 3000.

    Awaiting your kind reply.

  • Luke Maow Bear
    Hi Fishyton,

    Good day to you,

    Saw this tread and would like to get in touch with u to service my spinning reels.

    Shimano Stella 2013 C3000 & SW8000PG   Twinpower 2015 SW4000XG & SW5000PG
    Stradic New Model 3000.

    Awaiting your kind reply.

    ​You can service your reel at Shimano Singapore here is how. http://blog.fishingkaki.com/service-your-shimano-reels-at-shimano-singapore/

    @fishyton stopped servicing.
Sign In or Register to comment.
TRIPS
© Copyright 2020
All times are UTC